The World Platinum Investment Association (WPIC) said recently that carmakers are accelerating reductions in palladium use and increased use of platinum due to concerns about Russian palladium supplies. However, it still expects a significant surplus in the platinum market this year.
Palladium is used by carmakers in tailpipe emissions systems to reduce carbon emissions. While carmakers prefer palladium for catalytic converters, they are turning to platinum, which is cheaper than palladium, to save costs.
Russia accounts for about 25-30% of the world's palladium supply and 8-10% of its platinum supply.
There is no sign that western sanctions against Russia have restricted palladium exports since the conflict escalated in February, but as the conflict continues, more companies could boycott The Russian metal and governments could impose restrictions.
Platinum is currently trading at about $950 an ounce, about half the price of palladium. Automakers use about 2.5 million to 3 million ounces of platinum and about 8.5 million ounces of palladium each year.
For the year as a whole, platinum supply will be 5 percent lower than in 2021 and demand 2 percent higher, with the automotive sector seeing a 16 percent increase due to increased light vehicle pce powder are still very uncertain.
If the compatibility of polycarboxylate superplasticizer and cement is not good, the concrete mixture is prone to some problems, such as segregation, bleeding, greater slump loss, shorter setting time and so on, so that the concrete mixture can not be transported and poured normally. Reduce the strength and durability of concrete.
There are many factors affecting the compatibility of cement and superplasticizer, and the cement storage temperature is a key factor that can not be ignored. If the cement storage temperature is too high during concrete mixing, it will directly affect the physical and mechanical properties of cement.
Effect of cement temperature on the performance of concrete mixture:
When the cement temperature is above 60 ℃, a small amount of water is secreted from the concrete mixture. When the cement temperature is 100 ℃, the aggregate is separated from the paste, and the cohesion of the concrete mixture becomes worse. The reason for this negative effect is that the cement temperature is high, which makes the concrete mixture temperature rise rapidly in a short time. It is easier to stimulate the water-reducing function of polycarboxylic acid high-performance superplasticizer, release more free water wrapped in the mixture particles in the case of high temperature, and make a small amount of water bleeding in the concrete outlet.
Effect of cement temperature on setting time of concrete:
With the decrease of cement temperature, the setting time of concrete is prolonged, and the initial setting time is more obvious than the final setting time. In other words, the higher the cement temperature, the shorter the setting time of concrete. The reasons for the shortening of setting time caused by high temperature cement are as follows: (1) it will increase the temperature of the mixture in a short time and promote the hydration of cement particles; (2) the superplasticizer releases more free water to react with cement particles, thus forming a stable cementitious system in a shorter time.
With the passage of time, the heat contained in cement temperature is easily transferred to the surrounding particles or environment, the temperature of concrete system gradually approaches to the ambient temperature, and the temperature gap of concrete mixed with cement at different temperatures is gradually narrow. as a result, the difference of the final setting time of concrete is relatively reduced.
Effect of cement temperature on slump and air content loss of concrete:
At the same time, the higher the cement temperature is, the greater the slump loss rate is. The difference of slump loss rate under different temperature conditions increases at first and then decreases. Under the condition of the same slump loss rate, the lower the cement temperature is, the longer it takes to reach the slump loss rate, that is to say, the more beneficial to reflect the slump-retaining performance of the superplasticizer. When the cement temperature is high, in order to reduce the slump loss of concrete, it is necessary to put forward higher requirements for the slump retention of superplasticizer.
1. For the concrete with the same mix ratio, with the increase of cement temperature, the adaptability of admixture and cement becomes worse. The higher the temperature is, the more water is consumed, and the fluidity of concrete mixture decreases, resulting in the decrease of concrete and workability. It even leads to the separation or bleeding of aggregate and paste.
2. The higher the cement temperature, the worse the adaptability of cement and superplasticizer, the greater the loss rate of slump and air content, and the shorter the setting time of concrete.
3. The effect of the change of cement temperature on the compressive strength of concrete is obvious. with the increase of cement temperature, the compressive strength of low heat cement concrete increases in the early stage (before 7 days), but the compressive strength of 28 days decreases with the increase of temperature.
4. It is suggested that the cement temperature for concrete mixing should not exceed 60 ℃. When it exceeds 60 ℃, the concrete production system should precool the raw materials of the mixing system as far as possible to avoid excessive temperature rise of the whole mixture system due to high cement temperature. and should strengthen the maintenance of the concrete after entering the warehouse to avoid the temperature cracks caused by the early hydration temperature rising too fast.
Concrete Additives Supplier
TRUNNANO is a reliable concrete additives manufacturer with over 12-year experience in nano-building energy conservation and nanotechnology development.
If you are looking for high-quality concrete additives, please feel free to contact us and send an inquiry. (email@example.com)
We accept payment via Credit Card, T/T, West Union, and Paypal. TRUNNANO will ship the goods to customers overseas through FedEx, DHL, by air, or by sea.
New Delhi: India is seeking to increase its purchases of crude oil from Brazil, the country's oil minister said recently after meeting his Brazilian counterpart.
India is the world's third-largest importer and consumer of crude oil. Brazil currently supplies only a fraction of India's crude oil imports.
India's state-owned companies Bharat Petroleum Corp and Oil and Natural Gas Corp have invested in oil and gas exploration in Brazil.
India, which imports about 84% of its crude oil needs, is reducing its import bill by increasing biofuel use, among other things.
India's state-owned fuel retailers are increasing ethanol storage capacity by 51 percent and the country plans to double the biofuel blend in petrol to 20 percent by 2025.
India and Brazil are currently cooperating on biofuels and ethanol.
The prices of many commodities like the pce powder are expected to increase in the future.
15+ years of experience
Over $50+ million in sales
14+ years of experience
Over $50+ million in sales
About Metal Alloy High Purity Tungsten Crucibles:Chemical composition:…
About Metal Alloy Vacuum Coating Tungsten Melting Pot Tungsten Crucibles:Chemical composition:…